NACE-CIP1-001 Practice Exam Tests Latest Updated on Oct-2022
Pass NACE-CIP1-001 Exam in First Attempt Guaranteed Dumps!
NEW QUESTION 15
Dew point is the temperature at which
- A. water freezes.
- B. the air is saturated.
- C. humidity decreases
- D. condensation occurs.
Answer: D
NEW QUESTION 16
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. It depends on which power tool the Contractor selects
- B. It depends on which hand tool the Contractor selects
- C. Yes, because the 'two standards are not equivalent
- D. No, because there is no real difference in the standards
Answer: D
NEW QUESTION 17
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Use the job specification as a guide
- B. Use the product data sheet as a guide
- C. Call the coating manufacturer for clarification
- D. Call the person who wrote the specification for clarification
Answer: A
NEW QUESTION 18
An Inspector should change position when:
- A. The Inspector is convinced by verifiable facts
- B. The Owner can save some money by the change
- C. The Inspectors position is not the majority position
- D. Only when directed by the supervisor
Answer: A
NEW QUESTION 19
Prior to using Inspection Tools the inspector must:
- A. Read the manufactures' instructions
- B. Ensure the instrument is within calibration parameters
- C. a), b) & c)
- D. Be trained on how to use the instrument
Answer: C
NEW QUESTION 20
Silicone coatings are typically:
- A. Applied in very' thin films
- B. Applied in very thick films
- C. Used strictly in immersion service
- D. Used as a sacrificial primer
Answer: A
NEW QUESTION 21
Whenever dissimilar metals must join, the most common practice is to
- A. provide anodic protection to prevent corrosion.
- B. provide cathodic protection to prevent corrosion,
- C. avoid coating all connected dissimilar metals.
- D. coat all connected dissimilar metals.
Answer: D
NEW QUESTION 22
Stripe coats are generally applied to:
- A. Welds
- B. a), b), and c)
- C. Complex geometric shapes
- D. Edges and corners
Answer: B
NEW QUESTION 23
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. commercial blast cleaning.
- B. brush-off blast cleaning.
- C. white metal blast cleaning.
- D. near-white metal blast cleaning.
Answer: B
NEW QUESTION 24
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 25
Inspection documentation is important because:
- A. a) & b)
- B. Owners use the documentation for a variety of purposes
- C. It is the only deliverable item provided by the inspector
- D. a) only
Answer: B
NEW QUESTION 26
Removal of surface contaminants is done by:
- A. Waterjetting
- B. Abrasive blasting
- C. Scarifying
- D. A combination of methods
Answer: D
NEW QUESTION 27
The main responsibilities of the inspector are to
- A. direct and perform the work stated in the specification.
- B. observe and direct the work of the contractors.
- C. demonstrate to the contractor how to apply the coating.
- D. observe and report the quality of the work performed.
Answer: D
NEW QUESTION 28
Conventional spray is a good choice when:
- A. High production rates are required
- B. High transfer efficiency is required
- C. High viscosity coatings are being applied
- D. High quality finishes are required
Answer: D
NEW QUESTION 29
Solvents are added to coating formulations to
- A. increase film permeability.
- B. provide color.
- C. decrease film permeability.
- D. dissolve binders and form liquid coatings.
Answer: D
NEW QUESTION 30
Check abrasive blast pressure close to the
- A. substrate
- B. blast pot
- C. blast nozzle
- D. compressor
Answer: C
NEW QUESTION 31
NACE Level 1 Inspectors have been trained to perform:
- A. Visual inspection and Non-destructive testing
- B. Visual inspection only
- C. Visual inspection, Non-Destructive and Destructive testing
- D. All types of inspection
Answer: A
NEW QUESTION 32
Safety Data Sheets must be carefully reviewed by:
- A. All personnel involved in the job
- B. The Application personnel
- C. The Inspection personnel
- D. The Owner's personnel
Answer: A
NEW QUESTION 33
......
CIP Level 1 Free Certification Exam Material from CertkingdomPDF with 100 Questions: https://www.certkingdompdf.com/NACE-CIP1-001-latest-certkingdom-dumps.html
NACE-CIP1-001 Dumps Full Questions - Exam Study Guide: https://drive.google.com/open?id=1lc_uTc3KbN1u_N4028he7B44R_62Iu6I