Easily To Pass New NACE NACE-CIP1-001 Dumps with 100 Questions
Latest NACE-CIP1-001 Study Guides 2022 - With Test Engine PDF
NEW QUESTION 57
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Abrasive blast nozzles
- B. Airless spray equipment
- C. Hand tools
- D. Power tools
Answer: D
NEW QUESTION 58
A successful coating inspector must be able to
- A. look for problems or issues during application.
- B. advise the coating applicator on how to mix the coating.
- C. recommend the appropriate coating technique for the job to the contractor.
- D. apply the coating with expert accuracy.
Answer: A
NEW QUESTION 59
The NACE Inspector should perform tests for soluble salts:
- A. Prior to surface preparation
- B. After surface preparation
- C. When specified
- D. Prior to coating application
Answer: C
NEW QUESTION 60
A magnetic pull-off type gauge is a good choice when:
- A. Performing an adhesion test
- B. Accuracy is not required
- C. When an intrinsically safe tool is required
- D. When working on non-ferrous metals
Answer: C
NEW QUESTION 61
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor of your readings
- B. Call your supervisor
- C. Advise the Contractor he can proceed
- D. Advise the Contractor he cannot proceed
Answer: A
NEW QUESTION 62
Digital hygrometers
- A. determine relative humidity, air temperature, and dew point temperature:
- B. consist of a bimetallic sensing element protected from wind gusts.
- C. use a thermocouple in contact with the surface to measure temperature
- D. are used to measure temperature from a distance.
Answer: A
NEW QUESTION 63
If inspectors identify issues of non-conformance during an inspection, they should
- A. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- B. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- C. perform additional tests secretly to ensure there are no other potential issues at the site
- D. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
Answer: D
NEW QUESTION 64
ISO SA 3 is directly equivalent to:
- A. NACE No. 2/SSPC SP 10
- B. None of the above
- C. NACE No. 3/SSPC SP 6
- D. NACE No. 1/SSPC SP 5
Answer: B
NEW QUESTION 65
ISO ST 3 is described as:
- A. Very Thorough hand or power tool cleaning
- B. Thorough blast cleaning
- C. Very Thorough power tool cleaning
- D. Thorough hand tool cleaning
Answer: A
NEW QUESTION 66
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 80% of the specified minimum thickness
- B. 70% of the specified maximum thickness
- C. 100% of the specified maximum thickness
- D. 90% of the specified maximum thickness
Answer: A
NEW QUESTION 67
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. develops a polished surface, which is a poor anchor profile for most coatings
- B. damages structural elements thereby speeding up the corrosion process.
- C. scratches the surface too deeply resulting in uneven coating application
- D. develops a good anchor profile resulting in uneven coating application.
Answer: A
NEW QUESTION 68
Daily reports are important because:
Select All That Apply
- A. The information aids communication with supervisors.
- B. the information impacts future projects.
- C. Inspectors rarely change on a project.
- D. Management uses them to make personnel decisions.
Answer: A,B,D
NEW QUESTION 69
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks regardless
- B. Skip the checks and just record the same readings as you have been getting
- C. Keep doing the checks and consult the Owner's representative for direction
- D. Skip the checks as you are. confident the blast pressure is OK
Answer: C
NEW QUESTION 70
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- B. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- C. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- D. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
Answer: B
NEW QUESTION 71
The initial steel condition is important to the NACE Inspector because:
- A. If the steel is pitted more coating will be required
- B. It affects the final appearance after blasting
- C. The Inspector may have to reject the Steel
- D. Less abrasive is need if the mill Scale s gone
Answer: C
NEW QUESTION 72
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 2
- B. Level 4
- C. Level 3
- D. Level 1
Answer: C
NEW QUESTION 73
Stripe coats are generally applied to:
- A. a), b), and c)
- B. Edges and corners
- C. Complex geometric shapes
- D. Welds
Answer: A
NEW QUESTION 74
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Document the problem and advise the Contractor
- B. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- C. Break the blisters to see what's inside
- D. Document the problem and advise the Contractor and Owner's representative
Answer: D
NEW QUESTION 75
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. Pass/fail criteria
- B. A final conflict resolution method
- C. A method to grade surface profile
- D. A general guide
Answer: D
NEW QUESTION 76
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 8 to 10 mils (200 to 250 microns)
- B. 10 to 12 mils (250 to 300 microns)
- C. 5 to 6 mils (125 to 150 microns)
- D. 6 to 7 mils (150 to 175 microns)
Answer: D
NEW QUESTION 77
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- B. Default to the owner's Inspection and Test Plan
- C. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
- D. Bring the matter up at the pre-job conference
Answer: D
NEW QUESTION 78
......
NACE-CIP1-001 Dumps and Exam Test Engine: https://www.certkingdompdf.com/NACE-CIP1-001-latest-certkingdom-dumps.html
Get New NACE-CIP1-001 Practice Test Questions Answers : https://drive.google.com/open?id=1vc2W-ZD3pbluiGN82c1wB97qQqBt6Lcb