TMMI-P_IND Questions Pass on Your First Attempt Dumps for iSQI Other Certification Certified
TMMI-P_IND Practice Test Pdf Exam Material
NEW QUESTION 38
A test process assessment has been performed on a company developing systems for the medical industry.
Their systems are classified as safety critical. One of the shortcomings identified during the assessment is related to reliability testing. Although reliability was identified by the business as a critical issue, no formal approach and test techniques are being used for reliability testing.
Which of the following process areas would need specific attention to address the above mentioned shortcoming?
- A. Test Design and Execution
- B. Test Environment
- C. Product Quality Evaluation
- D. Non-Functional Testing
Answer: D
NEW QUESTION 39
Consider the following specific goal "Project Goals for Product Quality and their Priorities are Established".
To which of the following process areas does this specific goal belong?
- A. Test Policy and Strategy
- B. Test Measurement
- C. Advanced Reviews.
- D. Product Quality Evaluation
Answer: D
NEW QUESTION 40
What is the correct order for the following TMMi maturity levels (from low to high maturity)?
- A. Managed, Defined, Measured
- B. Managed, Measured, Defined
- C. Defined, Measured, Managed
- D. Defined, Managed, Measured
Answer: A
NEW QUESTION 41
An organization is facing too many defects occurring during production. As a consequence, an important test improvement goals for the next improvement cycle is to improve the quality (effectiveness) of the test cases.
Which of the following specific practices needs to be addressed, in the context of the improvement goal, as part of SG 1 "Perform Test Analysis and Design using Test Design Techniques" of the Test Design and Execution process area?
- A. Identify and Prioritize Test Charters
- B. Identify and Prioritize Test Conditions
- C. Specify Intake Test Procedure
- D. Develop and Prioritize Test Procedures
Answer: B
NEW QUESTION 42
Your organization performs code reviews and architectural reviews on a regular basis, in order to measure product quality early in the lifecycle.
This is an example of implementation of a specific practice from which TMMi level 4 process area?
- A. Quality Control
- B. Test Measurement
- C. Product Quality Evaluation
- D. Advanced Reviews
Answer: D
NEW QUESTION 43
Which of the following are specific goals of maturity level 4 process area AdvancedReviews?
1. Coordinate the peer review approach with the dynamic test approach
2. Perform peer reviews
3. Adjust the test approach based on review results early in the life cycle
4. Establish test performance indicators
5. Testing is performed using statistical methods
- A. 1, 3, 5
- B. 1 and 3
- C. 2, 3, 4
- D. 2, 4, 5
Answer: B
NEW QUESTION 44
Which of the statements about the Learning Phase of the IDEAL improvement framework is the TRUE?
- A. The Learning Phase is the last, but nevertheless an important phase of the improvement cycle.
- B. At the end of the Learning phase, all the improvement activities must have been completed and all improvement goals must have been achieved.
- C. Since most work has been done in the previous phases, the Learning Phase is not important.
- D. The Learning Phase includes the activities "Analyze and Validate", "Refine Solutions" and "Propose Future Actions".
Answer: A
NEW QUESTION 45
During a TMMi assessment the percentage of process achievement for the Test Planning process area has been determined at 40%.
Which of the following compliance ratings would you assign to Test Planning?
- A. Partly achieved
- B. Fully Achieved
- C. Not achieved
- D. Largely achieved
Answer: A
NEW QUESTION 46
Which of the following statements best describes the difference between a Specific Goal and a Generic Goal in the TMMi model?
- A. A Specific Goal is applicable to multiple process areas, whereas a Generic Goal is applicable to one process area only.
- B. Generic Goals are re-used from the CMMI and the Specific Goals are related to their implementation specifically for testing.
- C. A Generic Goal is applicable to multiple process areas, whereas a Specific Goal is applicable to one process area only.
- D. A Specific Goal is the institutionalization of a Generic Goal.
Answer: C
NEW QUESTION 47
Which of the following is a critical success factor that is typically most relevant while establishing improvements?
- A. Organize test improvement as a project
- B. The maturity of the development organization
- C. Management commitment
- D. Work on both long term and short term goals
Answer: D
NEW QUESTION 48
Given the following assessment phases:
1. Interview phase
2. Planning phase
3. Preparation phase
4. Reporting phase
Which of following orderings matches the generic assessment process?
- A. 2, 3, 1, 4
- B. 2, 1, 3, 4
- C. 3, 2, 1, 4
- D. 1, 2, 3, 4
Answer: A
NEW QUESTION 49
Which of the following activities is one that will typically be performed as part of the Diagnosing phase of the IDEAL test improvement cycle?
- A. Plan Actions
- B. Develop Recommendations
- C. Develop Solution
- D. Develop Approach
Answer: B
NEW QUESTION 50
Which of the following activities are part of the Acting phase of a test improvement cycle?
1. Set Priorities
2. Create Solutions
3. Plan Actions
4. Pilot Solutions
- A. 2, 3 and 4
- B. 2 and 4
- C. 1 and 2
- D. 1 and 3
Answer: B
NEW QUESTION 51
Improvement models can have a staged and/or continuous representation. The TMMi has been developed as a staged model.
Which of the following statements regarding a staged improvement model is TRUE?
- A. Practical experiences have shown that a staged representation is more difficult to use than a continuous representation due to its flexibility.
- B. A staged representation has no fixed set of levels to proceed through.
- C. A staged representation uses a predefined set of process areas to define an improvement path for an organization.
- D. An organization can select process areas for improvement based on business objectives.
Answer: C
NEW QUESTION 52
What is an example of an indirect benefit for a test improvement program?
- A. More reliable test estimates
- B. Increased personnel motivation
- C. Improvement in defect detection percentage
- D. Decrease in test execution lead-time
Answer: B
NEW QUESTION 53
Which of the following statements about the Acting phase of the IDEAL improvement model is TRUE?
- A. This phase normally consumes the least effort in the IDEAL process, at about 15% of the total.
- B. "Create solution" and "Implement Solution" are activities in this phase.
- C. "Plan actions" and "Implement solution" are activities in this phase.
- D. "Develop approach" and "Create solution" are activities in this phase.
Answer: B
NEW QUESTION 54
Which of the following specific goals would you be targeting during the implementation of the Test Policy and Strategy process area?
- A. Establish a Test Organization
- B. Establish Test Performance Indicators
- C. Establish a Test Approach
- D. Perform a Product Risk Assessment
Answer: B
NEW QUESTION 55
......
TMMI-P_IND [Dec-2021] Newly Released] Exam Questions For You To Pass: https://www.certkingdompdf.com/TMMI-P_IND-latest-certkingdom-dumps.html