Get 2024 Most Reliable Cisco 200-301 Training Materials
The Realest Study Materials 200-301 Dumps
NEW QUESTION # 510
Which two statements about RIPv2 are true? (Choose two)
- A. It is a link-state routing protocol
- B. its default administrative distances 120
- C. It must be manually enabled after RIP is configured as the routing protocol
- D. It uses multicast address 224.0.0.2 to share routing information between peers
- E. It is an EGP routing protocol
Answer: B,C
NEW QUESTION # 511
Which configuration register value can you set on a Cisco device so that it ignores the NVRAM when it boots?
- A. 0x2120
- B. 0x2142
- C. 0x2124
- D. 0x2102
Answer: B
NEW QUESTION # 512
Refer to the exhibit.
Which prefix does Router1 use for traffic to Host A?
- A. 10.10.13.144/28
- B. 10.10.10.0/28
- C. 10.10.13.208/29
- D. 10.10.13.0/25
Answer: C
NEW QUESTION # 513
After installing a new Cisco ISE server, which task must the engineer perform on the Cisco WLC to connect wireless clients on a specific VLAN based on their credentials?
- A. Enable the Even: Driven RRM.
- B. Enable the allow AAA Override
- C. Enable the Authorized MIC APs against auth-list or AAA.
- D. Disable the LAG Mode or Next Reboot.
Answer: B
Explanation:
In order to support centralized access control through a centralized AAA server such as the Cisco Identity Services Engine (ISE) or ACS, the IPv6 ACL can be provisioned on a per-client basis using AAA Override attributes. In order to use this feature, the IPv6 ACL must be configured on the controller and the WLAN must be configured with the AAA Override feature enabled.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-6/configuration- guide/b_cg76/b_cg76_chapter_0111001.pdf
NEW QUESTION # 514 
Answer:
Explanation:
NEW QUESTION # 515
Refer to the exhibit. Which two statements about the interface that generated the output are true? (Choose two)
- A. the security violation counter increments if packets arrive from a new unknown source address
- B. it has dynamically learned two secure MAC addresses
- C. the interface is error-diabled if packets arrive from a new unknown source address
- D. it has dynamically learned three secure MAC addresses
- E. learned MAC addresses are deleted after five minutes of inactivity
Answer: B,E
NEW QUESTION # 516
Refer to the exhibit.
IP connectivity and OSPF are preconfigured on all devices where necessary. Do not make any changes to the IP addressing or OSPF. The company policy uses connected interfaces and next hops when configuring static routes except for load balancing or redundancy without floating static. Connectivity must be established between subnet 172.20.20.128/25 on the Internet and the LAN at 192.168.0.0/24 connected to SW1:
1. Configure reachability to the switch SW1 LAN subnet in router R2.
2. Configure default reachability to the Internet subnet in router R1.
3. Configure a single static route in router R2 to reach to the Internet subnet considering both redundant links between routers R1 and R2. A default route is NOT allowed in router R2.
4. Configure a static route in router R1 toward the switch SW1 LAN subnet where the primary link must be through Ethernet0/1. and the backup link must be through Ethernet0/2 using a floating route. Use the minimal administrative distance value when required.
Answer:
Explanation:
Answer as below configuration:
On R2:
Enable
Conf t
Ip route 192.168.1.0 255.255.255.0 10.10.31.1
On R1:
Enable
Conf t
Ip route 0.0.0.0 0.0.0.0 10.10.13.3
On R2
Ip route 172.20.20.128 255.255.255.128 e0/2
Ip route 172.20.20.128 255.255.255.128 e0/1
On R1
Ip route 192.168.0.0 255.255.255.0 e0/1
Ip route 192.168.0.0 255.255.255.0 10.10.12.2 3
Save all configurations after every router from anyone of these command Do wr Or Copy run start
NEW QUESTION # 517
Drag and drop the statements about AAA services firm the left onto the corresponding AAA services on the right Not all options are used.
Answer:
Explanation:
NEW QUESTION # 518
An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any of three addresses
192.168.30.1, 192.168.3.2, 192.168.3.3 Which configuration should be used?
- A. Option B
- B. Option D
- C. Option C
- D. Option A
Answer: C
NEW QUESTION # 519
Refer to the exhibit.
Which prefix does Router 1 use for traffic to Host A?
- A. 10.10.13.144/28
- B. 10.10.10.0/28
- C. 10.10.13.208/29
- D. 10.10.13.0/25
Answer: C
Explanation:
Host A address fall within the address range. However, if more than one route to the same subnet exist (router will use the longest stick match, which match more specific route to the subnet). If there are route 10.10.13.192/26 and 10.10.13.208/29, the router will forward the packet to /29 rather than /28.
NEW QUESTION # 520
An engineer configured an OSPF neighbor as a designated router.
Which state verifies the designated router is in the proper mode?
- A. Init
- B. 2-way
- C. Full
- D. Exchange
Answer: C
NEW QUESTION # 521
Refer to the exhibit.
An access list is created to deny Telnet access from host PC-1 to RTR-1 and allow access from all other hosts A Telnet attempt from PC-2 gives this message:"% Connection refused by remote host" Without allowing Telnet access from PC-1, which action must be taken to permit the traffic?
- A. Remove the access-class 10 in command from line vty 0.4.
- B. Add the ip access-group 10 out command to interface g0/0.
- C. Add the access-list 10 permit any command to the configuration
- D. Remove the password command from line vty 0 4.
Answer: C
NEW QUESTION # 522
Drag and Drop Question
Drag and drop the statements about networking from the left onto the corresponding networking types on the right.
Answer:
Explanation:
NEW QUESTION # 523
In software defined architectures, which plane is distributed and responsible for traffic forwarding?
- A. control plane
- B. policy plane
- C. management plane
- D. data plane
Answer: D
Explanation:
Section: Automation and Programmability
NEW QUESTION # 524
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2.
Based on the information in the graphic, what is the cause of this problem?
- A. A backup designated router needs to be added to the network.
- B. The priority on R1 should be set higher.
- C. The OSPF area is not configured properly.
- D. The hello and dead timers are not configured properly.
- E. The cost on R1 should be set higher.
- F. The OSPF process ID numbers must match.
Answer: D
NEW QUESTION # 525
......
Official Preparation Path
The vendor recommends that all aspiring candidates should first gain the required skills before continuing with their certification journey. And one of the best ways to achieve this is through the official training course, which is Implementing and Administering Cisco Solutions (CCNA) v1.0. Let’s find out what the actual course content entails.
Are There Any Requisites for Obtaining CCNA Certification?
There are no official prerequisites for this certificate. However, it will be an advantage if you have one or more years of experience in administering and implementing Cisco solutions, a deep understanding of networking basics, and knowledge of basic IP addressing.
To prepare for the exam, Cisco offers a variety of resources, including self-paced e-learning courses, instructor-led training, virtual labs, study groups, and practice exams. It is recommended that you have at least one year of networking experience before taking the exam, but this is not a requirement.
LATEST 200-301 Exam Practice Material: https://www.certkingdompdf.com/200-301-latest-certkingdom-dumps.html
New 200-301 Actual Exam Dumps, Cisco Practice Test: https://drive.google.com/open?id=1imUtYC5WVECr3EzBleNKk2zEkoQDbbXs