300-710 Free Exam Study Guide! (Updated 145 Questions)
300-710 Dumps for CCNP Security Certified Exam Questions & Answer
Domain #2. Configuration
The next 30% of the syllabus is based on the configuration principles. In this section, a detailed understanding of setting up system settings in the Cisco Firepower Management Center can be gained. When mastering this module is in progress, obtaining skills related to accessing control, intrusion, malware, DNS, identity, SSL, prefilter, and network discovery is required. Besides, this section explains the concepts like application detector, correlation, actions, and object management. Intrusion rules, device management, NAT, VPN, QoS, certificates, and platform setting are other covered topics.
Career Prospects and Salary Outlook
Clearing the Cisco 300-710 exam can elevate your career to a new level by enhancing your knowledge and skills, increasing your credibility, and providing you with a competitive edge over your peers. After passing this test and obtaining Cisco Certified Specialist – Network Security Firepower or CCNP Security, you will explore a variety of employment opportunities. The positions that will become available to you after getting certified are as follows:
- Network Security Engineer
- Systems Engineer
- Security Consultant
- Network Administrator
- Development Operations (DevOps) Engineer
- Security Administrator
- Network Manager
- Network Engineer
- Senior Technical Consultant
Passing the Cisco 300-710 exam can be also highly beneficial in terms of higher remuneration. According to PayScale, the average annual salary for the certificate holders amounts to $112,674. Depending on the role, you can earn even more than this figure. Thus, the average income of a Network Manager is around $131,000 per annum, while the position of a Senior Technical Consultant can bring you as much as $140,000 per year.
NEW QUESTION 56
Which command is entered in the Cisco FMC CLI to generate a troubleshooting file?
- A. system support diagnostic-cli
- B. sudo sf_troubleshoot.pl
- C. show tech-support chassis
- D. show running-config
Answer: B
Explanation:
Reference: https://www.cisco.com/c/en/us/support/docs/security/sourcefire-defense-center/117663-technote-SourceFire-00.html
NEW QUESTION 57
An engineer is setting up a new Firepower deployment and is looking at the default FMC policies to start the implementation. During the initial trial phase, the organization wants to test some common Snort rules while still allowing the majority of network traffic to pass. Which default policy should be used?
- A. Maximum Detection
- B. Connectivity Over Security
- C. Balanced Security and Connectivity
- D. Security Over Connectivity
Answer: B
Explanation:
Section: Deployment
NEW QUESTION 58
What is the result of specifying of QoS rule that has a rate limit that is greater than the maximum throughput of an interface?
- A. Matching traffic is not rate limited.
- B. The system repeatedly generates warnings.
- C. The rate-limiting rule is disabled.
- D. The system rate-limits all traffic.
Answer: A
NEW QUESTION 59
Which object type supports object overrides?
- A. security group tag
- B. network object
- C. time range
- D. DNS server group
Answer: B
NEW QUESTION 60
There is an increased amount of traffic on the network and for compliance reasons, management needs visibility into the encrypted traffic What is a result of enabling TLS'SSL decryption to allow this visibility?
- A. It is not subject to any Privacy regulations
- B. It will fail if certificate pinning is not enforced
- C. It prompts the need for a corporate managed certificate
- D. It has minimal performance impact
Answer: C
NEW QUESTION 61
What is the difference between inline and inline tap on Cisco Firepower?
- A. Inline mode cannot do SSL decryption.
- B. Inline tap mode can send a copy of the traffic to another device.
- C. Inline mode can drop malicious traffic.
- D. Inline tap mode does full packet capture.
Answer: C
NEW QUESTION 62
Which two statements about deleting and re-adding a device to Cisco FMC are true? (Choose two.)
- A. The Cisco FMC web interface prompts users to re-apply access control policies.
- B. No option to delete and re-add a device is available in the Cisco FMC web interface.
- C. Before re-adding the device in Cisco FMC, you must add the manager back in the device.
- D. No option to re-apply NAT and VPN policies during registration is available, so users need to re-apply the policies after registration is completed.
- E. An option to re-apply NAT and VPN policies during registration is available, so users do not need to re- apply the policies after registration is completed.
Answer: A,D
NEW QUESTION 63
What is the advantage of having Cisco Firepower devices send events to Cisco Threat Response via the security services exchange portal directly as opposed to using syslog?
- A. Supports all devices that are running supported versions of Cisco Firepower.
- B. Cisco Firepower devices do not need to be connected to the Internet.
- C. All types of Cisco Firepower devices are supported.
- D. An on-premises proxy server does not need to be set up and maintained.
Answer: D
NEW QUESTION 64
Which command is typed at the CLI on the primary Cisco FTD unit to temporarily stop running high- availability?
- A. configure high-availability resume
- B. system support network-options
- C. configure high-availability disable
- D. configure high-availability suspend
Answer: C
NEW QUESTION 65
What is the maximum bit size that Cisco FMC supports for HTTPS certificates?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/security/firepower/610/configuration/guide/fpmc-config- guide-v61/system_configuration.html
NEW QUESTION 66
An engineer is setting up a new Firepower deployment and is looking at the default FMC policies to start the implementation During the initial trial phase, the organization wants to test some common Snort rules while still allowing the majority of network traffic to pass Which default policy should be used?
- A. Maximum Detection
- B. Connectivity Over Security
https://www.cisco.com/c/en/us/td/docs/security/firepower/623/fdm/fptd-fdm-config-guide-623/fptd-fdm-intrusion.html - C. Balanced Security and Connectivity
- D. Security Over Connectivity
Answer: C
NEW QUESTION 67
A network engineer is tasked with minimising traffic interruption during peak traffic limes. When the SNORT inspection engine is overwhelmed, what must be configured to alleviate this issue?
- A. Enable Pre-filter policies before the SNORT engine failure.
- B. Enable IPS inline link state propagation
- C. Enable Automatic Application Bypass.
- D. Set a Trust ALL access control policy.
Answer: C
NEW QUESTION 68
What is a functionality of port objects in Cisco FMC?
- A. to add any protocol other than TCP or UDP for source port conditions in access control rules.
- B. to represent all protocols in the same way
- C. to represent protocols other than TCP, UDP, and ICMP
- D. to mix transport protocols when setting both source and destination port conditions in a rule
Answer: C
Explanation:
Section: Management and Troubleshooting
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config- guide-v62/reusable_objects.html
NEW QUESTION 69
An engineer is configuring a second Cisco FMC as a standby device but is unable to register with the active unit. What is causing this issue?
- A. The primary FMC currently has devices connected to it.
- B. There is only 10 Mbps of bandwidth between the two devices.
- C. The licensing purchased does not include high availability
- D. The code versions running on the Cisco FMC devices are different
Answer: C
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config-guide-v62/firepower_management_center_high_availability.html
NEW QUESTION 70
Which command is run at the CLI when logged in to an FTD unit, to determine whether the unit is managed locally or by a remote FMC server?
- A. show managers
- B. show running-config | include manager
- C. show configuration session
- D. system generate-troubleshoot
Answer: A
NEW QUESTION 71
An organization wants to secure traffic from their branch office to the headquarter building using Cisco Firepower devices, They want to ensure that their Cisco Firepower devices are not wasting resources on inspecting the VPN traffic. What must be done to meet these requirements?
- A. Configure the Cisco Firepower devices to ignore the VPN traffic using prefilter policies
- B. Configure the Cisco Firepower devices to bypass the access control policies for VPN traffic.
- C. Enable a flexconfig policy to re-classify VPN traffic so that it no longer appears as interesting traffic
- D. Tune the intrusion policies in order to allow the VPN traffic through without inspection
Answer: C
NEW QUESTION 72
Which CLI command is used to generate firewall debug messages on a Cisco Firepower?
- A. system support platform
- B. system support dump-table
- C. system support ssl-debug
- D. system support firewall-engine-debug
Answer: D
Explanation:
Reference:
https://www.cisco.com/c/en/us/support/docs/security/firepower-ngfw/212330-firepower- management-center-display-acc.html
NEW QUESTION 73
An engineer is setting up a new Firepower deployment and is looking at the default FMC policies to start the implementation During the initial trial phase, the organization wants to test some common Snort rules while still allowing the majority of network traffic to pass Which default policy should be used?
- A. Maximum Detection
- B. Connectivity Over Security
- C. Balanced Security and Connectivity
- D. Security Over Connectivity
Answer: C
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/security/firepower/623/fdm/fptd-fdm-config-guide-623/fptd-fdm-intrusion.html
NEW QUESTION 74
Which Cisco Firepower Threat Defense, which two interface settings are required when configuring a routed interface? (Choose two.)
- A. Redundant Interface
- B. Speed
- C. Media Type
- D. Duplex
- E. EtherChannel
Answer: B,D
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/security/firepower/610/fdm/fptd-fdm-config-guide-610/fptd-fdm-interfaces.html
NEW QUESTION 75
An engineer configures an access control rule that deploys file policy configurations to security zones, and it cause the device to restart. What is the reason for the restart?
- A. Source or destination security zones in the access control rule matches the security zones that are associated with interfaces on the target devices.
- B. Source or destination security zones in the source tunnel zone do not match the security zones that are associated with interfaces on the target devices.
- C. The source tunnel zone in the rule does not match a tunnel zone that is assigned to a tunnel rule in the source policy.
- D. The source tunnel zone in the rule does not match a tunnel zone that is assigned to a tunnel rule in the destination policy.
Answer: A
NEW QUESTION 76
Which Firepower feature allows users to configure bridges in routed mode and enables devices to perform Layer 2 switching between interfaces?
- A. FlexConfig
- B. IRB
- C. SGT
- D. BDI
Answer: B
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/security/firepower/620/relnotes/ Firepower_System_Release_Notes_Version_620/new_features_and_functionality.html
NEW QUESTION 77
What is the advantage of having Cisco Firepower devices send events to Cisco Threat response via the security services exchange portal directly as opposed to using syslog?
- A. An on-premises proxy server does not need to set up and maintained
- B. Firepower devices do not need to be connected to the internet.
- C. Supports all devices that are running supported versions of Firepower
- D. All types of Firepower devices are supported.
Answer: A
NEW QUESTION 78
Which two routing options are valid with Cisco Firepower Threat Defense? (Choose two.)
- A. BGPv4 in transparent firewall mode
- B. BGPv6
- C. ECMP with up to three equal cost paths across multiple interfaces
- D. ECMP with up to three equal cost paths across a single interface
- E. BGPv4 with nonstop forwarding
Answer: B,D
Explanation:
Section: Configuration
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/security/firepower/601/configuration/guide/fpmc-config- guide-v601/fpmc-config-guide-v60_chapter_01100011.html#ID-2101-0000000e
NEW QUESTION 79
......
Understanding the General Outline
Cisco 300-710 is a well-structured exam that aims at directional learning. It is divided into four main domains, and each of them is focused on a different skill set and imparts updated cognizance.
Use Real 300-710 Dumps - 100% Free 300-710 Exam Dumps: https://www.certkingdompdf.com/300-710-latest-certkingdom-dumps.html
Realistic Verified 300-710 exam dumps Q&As - 300-710 Free Update : https://drive.google.com/open?id=1aMw3MaKSLWIoCACtdybhZfBOgeB7oI57